eSIM Packaging: The 5×6 mm vs 3×3 mm Decision That Can Cost You a PCB Respin

Share
eSIM Packaging: The 5×6 mm vs 3×3 mm Decision That Can Cost You a PCB Respin
Here is a decision that quietly shapes your BOM, your assembly yield and your launch date: which physical package your eSIM uses.
It looks like a footnote. It is not. Get it wrong and you are not swapping a component — you are re-spinning a board, re-cutting a stencil and re-qualifying an assembly line. Get it right and the SIM becomes one of the least interesting parts of your design, which is exactly what you want.
This guide is the short version we wish every hardware team read before releasing a footprint.

The fast answer

Both 5×6 mm and 3×3 mm eSIM packages exist. They are not the same standard, and they are not interchangeable:
  • 5×6 mm = MFF2 — the mainstream 8-pin soldered eSIM defined in ETSI TS 102 671, and the part most suppliers actually stock.
  • 3×3 mm = MFF3 — a 10-pin package commonly described as JEDEC MO-229F-compatible. Smaller body, finer pitch, thinner vendor list.
  • 2×2 mm = MFF4 — an 8-pin package now moving into volume production for wearables and dense modules.
Different pin counts. Different pad layouts. Different pitches. A board built for one will not accept another.

One table, three decisions

Package Body size Pins Pitch Thickness Defined by Best for
1FF–4FF 85.6×54 to 12.3×8.8 mm 6–8 contacts n/a 0.67–0.76 mm ISO/IEC 7810, ETSI TS 102 221 Removable SIM
MFF1 5×6 mm 8 (dual pads) 1.27 mm 0.50–0.65 mm ETSI TS 102 671 Socketed M2M
MFF2 5×6 mm 8 1.27 mm ≈0.75–0.9 mm ETSI TS 102 671 Mainstream soldered eSIM
MFF3 3×3 mm 10 0.5 mm (typical) 0.65 mm Referenced to JEDEC MO-229F Dense wearables, compact IoT
MFF4 2×2 mm 8 Confirm in datasheet Per MO-229F JEDEC MO-229F-compatible Ultra-compact devices
WLCSP Die-scale Vendor-specific Vendor-specific Vendor-specific Vendor-specific Modules with no spare space

One thing worth repeating: ETSI TS 102 671 defines only MFF1 and MFF2. MFF3 and MFF4 sit in the JEDEC MO-229F family and are supported by far fewer silicon vendors. If a datasheet calls a 3×3 mm part "small MFF2", treat that as marketing language, not a standard.

MFF2 (5×6 mm): the safe default

MFF2 is what most engineers picture when they hear "eSIM chip": an 8-lead DFN, 1.27 mm pitch, an exposed die pad in the centre, industrial temperature range of −40 °C to +105 °C, shipped 4,000 pieces to a 13-inch reel.

Why it keeps winning:

  • Second sources. Multiple silicon vendors and distributors stock it, so a shortage does not stop your line.

  • Assembly-friendly. 1.27 mm pitch is forgiving. Standard stencils, standard placement, standard reflow.

  • Test-friendly. DFN8 sockets are cheap and everywhere, which means you can validate a batch without soldering anything.

The exposed pad is not an electrical node. It is there for heat and mechanical anchoring. Tie it to ground and forget it.

Five pins, two mistakes

The pin mapping is consistent across ETSI TS 102 671 and the MFF2 datasheets from STMicroelectronics, Avnet and Soracom:

Package pin UICC contact Signal Notes
1 C5 GND Ground
2 C6 Not connected Reserved
3 C7 I/O Serial data, T=0
4 C8 Not connected Reserved
5 C4 Not connected Reserved
6 C3 CLK Clock
7 C2 RST Reset
8 C1 VCC 1.62–5.5 V

Only five signals matter. The other three pins stay isolated — that is correct, not a shortcut.

Most first-pass failures come from two omissions, both cheap to fix and expensive to discover late:

  1. No pull-up on I/O. ST's reference design calls for a 20 kΩ external pull-up. Without it, some readers fail to activate the card reliably.

  2. No local decoupling. A 100 nF capacitor placed as close as possible to VCC prevents the kind of intermittent behaviour that costs days of debugging.

Neither part costs more than a few cents. Both cost weeks if missing.

MFF3 (3×3 mm): the space saver with a documentation gap

MFF3 cuts the body to 3×3 mm and the profile to 0.65 mm — but adds two pins and halves the pitch. You gain board area and take on a tighter process window: finer stencil, more precise placement, a reflow profile that will not tombstone a 10-lead part.

The bigger risk is not assembly. It is documentation.

Generic DFN 3×3 10-lead test sockets are easy to buy and inexpensive. But a socket's pin numbers are mechanical positions, not SIM signals. Public documentation mapping MFF3 pins to UICC contacts is scarce, and very few MFF3 eUICCs are in volume today. The major vendors' published datasheets concentrate on MFF2, MFF4 and WLCSP.

How to de-risk a 3×3 design

  1. Request the pin assignment table for the exact part number from the silicon vendor — not the package drawing, the pin table.

  2. Buy a small batch of samples plus a DFN 3×3 10-lead socket.

  3. Identify VCC and GND with a multimeter, then confirm CLK, I/O and RST by powering the part through a PC/SC reader and watching for the ATR.

  4. Only after that, release the footprint. A five-piece prototype run is always cheaper than a respin.

If a supplier cannot give you the pin table, that is your answer: pick a different supplier.

MFF4 (2×2 mm) and WLCSP: when every millimetre counts

MFF4 shrinks the soldered eSIM to a 2×2 mm, 8-pin body for wearables, trackers and dense gateways, while keeping full remote provisioning. Some product lines label the same package USON8-6 — another reason to check the drawing, not the name.

WLCSP goes smaller by packaging at wafer scale. It lives inside modules where the SIM is one component among many, and pinouts are vendor-specific. Expect less flexibility and harder rework.

Adapters and test fixtures: the fastest way to validate

If you need to test a soldered eSIM against legacy equipment, qualification rigs or evaluation kits, an adapter card gets you there quickly. Because only five signals matter, the routing is short:

MFF2 pin Card contact Signal
8 C1 VCC
7 C2 RST
6 C3 CLK
1 C5 GND
3 C7 I/O
2, 4, 5 — Leave open

Practical notes:

  • Keep the card's contact pads flush and flat — a raised pad changes how the card sits in the reader.

  • Route VCC and GND with a solid ground return; SIM current spikes are brief but real.

  • Put the 20 kΩ pull-up and 100 nF decoupling on the adapter if the host does not provide them.

  • A 3×3 mm design needs its own PCB. The 10th pin has no counterpart on an 8-pin footprint.

Which package for your next build?

Your priority Pick Why
Supply security and second sources MFF2 (5×6 mm) Broadest availability, multiple vendors, forgiving pitch
Smallest possible board area MFF3 (3×3 mm) or MFF4 (2×2 mm) Smaller body, but fewer vendors and tighter assembly
Fastest route to a working prototype MFF2 + DFN8 socket Cheap sockets, no soldering, quick validation
Absolute minimum footprint inside a module WLCSP Die-scale, vendor-specific, harder to rework

The rule we give most teams: choose MFF2 unless the mechanical envelope truly cannot fit it. A 3×3 mm part can save a few square millimetres and cost you weeks in tooling, stencil adjustment and vendor qualification. That trade is rarely worth it unless the product's size depends on it.

FAQ

Is 3×3 mm just a smaller MFF2?

No. MFF3 has 10 pins at a finer pitch and a different pad layout. The five SIM signals behave the same, but the physical mapping must come from the chip datasheet.

Can I socket an eSIM for engineering work?

Yes. DFN test sockets exist for both 8-lead 5×6 mm and 10-lead 3×3 mm bodies, typically US$8–12 at low volume. Use them for validation and small-batch programming, not production.

Do I need to route all eight MFF2 pins?

No. Five pins carry signals. Pins 2, 4 and 5 are reserved and stay isolated.

Does the exposed pad need solder?

Yes, for thermal and mechanical reasons — but connect it to ground, never to VCC or I/O.

Building something that needs a soldered eSIM?

Tell us the mechanical envelope, the volume and the host interface. We can help you pick the package, check the footprint against the real datasheet, and supply adapter or fixture hardware so you can validate before you commit tooling.

Send us your drawing and your target volume — we will tell you which package survives your supply chain.


Packaging details vary by silicon vendor. Verify pin assignment, pitch and thickness against the datasheet for the exact part number before releasing a footprint.

eSIM Is Convenient — and That Convenience Is the Security Problem

eSIM Is Convenient — and That Convenience Is the Security Problem

Leave comments

Please note, comments must be approved before they are published.

Empty content. Please select article to preview

Sunday,Monday,Tuesday,Wednesday,Thursday,Friday,Saturday
January,February,March,April,May,June,July,August,September,October,November,December
Not enough items available. Only [max] left.
Add to WishlistBrowse WishlistRemove Wishlist
Shopping cart

Your cart is empty.

Return To Shop

Add Order Note Edit Order Note
Estimate Shipping
Add A Coupon

Estimate Shipping

Add A Coupon

Coupon code will work on checkout page